Data set 01
1999 Philips E-Z
Published operating points and test conditions from this source.
Cathode Ray
Characteristic
INSTRUMENT CATHODE-RAY TUBE
14 cm
Final accelerator voltage Vg10l2)
8.5 kV
Display area (10 x 8 divisions of [1]
9 mm
Display area (10 x 8 divisions of [2]
90x72 mm
horizontal My
9.5 V
vertical My
41 V
Writing speed
25 div/µs
Useful screen dimensions min
90x72 mm
horizontal min
90 mm
vertical min
72 mm
and vertical directions max
6 mm
Heater current I
300 mA
Heater current Iy
300 mA
Heater current Lgre
300 mA
Net mass approx
1.1 kg
Overall length (socket included) max
445 mm
Face dimensions max
100x 120 mm
| 95 _
9 s
{1} The bulge at the frit seal may increase the indicated maximum dimensions by not more than
3 mm
(2) Minimum length of cable
420 mm
sub-division
1.8 mm
line width
0.15 mm
Fig. 6 Detail of side contact dot diameter
0.3 mm
Deflection coefficient
9.5 V
Mx max
10.5 V
Y max
4.4 V
Line width at the centre of the screen l.w
0.36 mm
Grid drive for [1]
10 µA
Grid drive for [2]
25 A
Collimator voltage Vg7 :?
0 V
First accelerator voltage Vg2'.Vg2" 2?
40 V
capable of supplying
0.5 mA
conditions, adjusted for optimum spot size at a beam current I
10 µA
approx
2.5 div/µs
9. A graticule, consisting of concentric rectangles of [1]
88 mm
9. A graticule, consisting of concentric rectangles of [2]
70 mm
9. A graticule, consisting of concentric rectangles of [3]
86 mm
9. A graticule, consisting of concentric rectangles of [4]
68.5 mm
electrode. The pulse amplitude required is approximately [1]
9 V
electrode. The pulse amplitude required is approximately [2]
15 V
potential for about
100 ms
less than
300 ms
For non-store operation, it is sufficient to make the backing electrode about
35 V
a. Adjust the cathode current of each viewing gun to
0.4 mA
uniformity. This voltage will be approximately
80 V
Capacitance
x1 to all other elements except x9 Cx1(x2)
6.5 pF
x2 to all other elements except x4 Cx2(x1)
6.5 pF
X1 to X2 Cx1x2
25 pF
g1 to all other elements Cg1
55 pF
g1’ to all other elements Cg1'
55 pF
g1 to all other elements Cq1”
5.5 pF
k to all other elements
4.5 pF
g7 to all other elements
40 pF
gg to all other elernents Cgg
75 pF
Other
Final accelerator voltage Vg10l® min
7000 V
max
2100 A
Astigmatism control electrode voltage Vg4 min
1200 V
Focusing electrode voltage Vg3 max
1000 V
Final accelerator voltage Vg1ot® min
5500 V
non-storage operation —Vgg min
25 V
max
180 A
Collector voltage Vgg min
120 V
The current required under typical operating conditions without a mu-metal shield being used is max.
20 mA
means that a current of max [1]
12.56 mA
means that a current of max [2]
12 V
when the coils are connected in series or a
6 V
With L3 and L4 connected in series according to Fig
11 A