Frequency range
9460 MHz
Frequency range 9360 to 9460 MHz
Typical peak output power
45 kW
Typical peak output power 45 kW
Heater current at 3.0V
3.5 A
Heater current at 3.0V . 3.5 A
Cathode heating time (minimum)
20 s
Cathode heating time (minimum) 20 s
Anode voltage (peak)
16 kV
Anode voltage (peak) 10 16 kV
Anode current {peak)
12 A
Anode current {peak) — 12 A
Pulse length
2
Pulse length . . . . . . . . . - 2.0 MS
V.S.W.R. at the output coupler
1 V
V.S.W.R. at the output coupler . — 1.6:1
Heater voitage
1.5 A
Heater voitage . 1.5 A
Anode current (peak)
12
Anode current (peak) 12 Al
Pulse length
1
Pulse length 1.0 us
Pulse repetition rate
1000 s
Pulse repetition rate 1000 p.p.s.
Anode voltage {peak)
1.1 kV
Anode voltage {peak) 1.1 kV
Output power (peak)
45 kW
Output power (peak) 45 kW
Output power {mean)
45 W
Output power {mean) 45 W
Heater voltage (fortest)
1.5
Heater voltage (fortest) . 1.5 1.5 1.5 \%
Anode current {mean)
12 mA
Anode current {mean) . . 12 12 12 mA
Anode voltage (peak)
12.5 kV
Anode voltage (peak) .10.5 12.5 - - - - kV
Output power {mean) . 35
35 W
Output power {mean) . 35 — - - - - W
Frequency pulling
15 MHz
Frequency pulling . . — — — 15 — — MHz
Output power (mean)
28 W
Output power (mean) . . .. . . . . 28 W min
R.F. bandwidth at % power (Oscnlauon2)
3 MHz
R.F. bandwidth at % power (Oscnlauon2) .. 3.0 MHz max
Frequency
9460 MHz
Frequency . 9360 to 9460 MHz
1. With no anode input power.
1
1. With no anode input power.
mum capacitance of 4000pF shunted across the heater directly at the
4000
mum capacitance of 4000pF shunted across the heater directly at the
input terminals; in some cases a capacitance as high as 2uF may be nec-
2 a
input terminals; in some cases a capacitance as high as 2uF may be nec-
teading edge of the voltage pulse above 80% amplitude. Any capaci-
80
teading edge of the voltage pulse above 80% amplitude. Any capaci-
At anode temperature 25°C
25 °C
At anode temperature 25°C.
The maximum bandwidth in MHz is given by 3.0/(pulse length in us)
3 MHz
The maximum bandwidth in MHz is given by 3.0/(pulse length in us).
The mean anode current is varied between 12 and 14mA
14
The mean anode current is varied between 12 and 14mA.
of the number of input pulses applied during this 30 second period
30
of the number of input pulses applied during this 30 second period.
Pulses are definea as missing when the r.f. energy level is less than 70%
70
Pulses are definea as missing when the r.f. energy level is less than 70%
of the normal energy level in the frequency range 9360 to 9460MHz
9460
of the normal energy level in the frequency range 9360 to 9460MHz.
11
11 a
11. When a signal of the same frequency as the valve operating frequency is
The v.s.w.r. is tested to be greater than 6:1 and its phase such that a
1 v
The v.s.w.r. is tested to be greater than 6:1 and its phase such that a
12
15
12. Over the range 8 to 15mA, no pulses shall be missing when viewed with
13
3
13. Measured with heater voltage of 3.0V and no anode input power, the
heater current limits are 3.0A minimum, 4.0A maximum
4
heater current limits are 3.0A minimum, 4.0A maximum.
14
14
14. Design test only. The maximum frequency change with anode tempera-
2. The common cathode connection is indicated by a letter ‘C' on this
2 a
2. The common cathode connection is indicated by a letter ‘C' on this
