Data set 01
1962 ITT
Published operating points and test conditions from this source.
TravelingWave
Other
gain and [1]
8000 MHz
gain and 8000 to 9600 mc frequency range. It is constructed in a rugged
gain and [2]
9600 MHz
gain and 8000 to 9600 mc frequency range. It is constructed in a rugged
Heater Voltage [1]
6.3 V
Heater Voltage 6.3 (x10%) volts
Heater Voltage [2]
0 V
Heater Voltage 6.3 (x10%) volts
Heater current
850 mA
Heater current 0.85 amperes
Maximum Anode Voltage (Note [1]
1 V
Maximum Anode Voltage (Note 1) 1500 volts
Maximum Anode Voltage (Note [2]
1500 V
Maximum Anode Voltage (Note 1) 1500 volts
Maximum Shell Current (Note [1]
2 A
Maximum Shell Current (Note 2 and Note 6) 3 ma
Maximum Shell Current (Note [2]
6 A
Maximum Shell Current (Note 2 and Note 6) 3 ma
Maximum Shell Current (Note [3]
3 A
Maximum Shell Current (Note 2 and Note 6) 3 ma
Maximum Collector Voltage (Note [1]
3 V
Maximum Collector Voltage (Note 3) 1600 volts
Maximum Collector Voltage (Note [2]
1600 V
Maximum Collector Voltage (Note 3) 1600 volts
Maximum Collector Dissipation {(Note [1]
4 W
Maximum Collector Dissipation {(Note 4) 25 watts
Maximum Collector Dissipation {(Note [2]
25 W
Maximum Collector Dissipation {(Note 4) 25 watts
Maximum Control Electrode Voltage (Note [1]
5 V
Maximum Control Electrode Voltage (Note 5) -250 volts
Maximum Control Electrode Voltage (Note [2]
-250 V
Maximum Control Electrode Voltage (Note 5) -250 volts
Maximum Frequency
9600 MHz
Maximum Frequency 9600 mc
Minimum Frequency
8000 MHz
Minimum Frequency 8000 mc
Maximum Glass Temperature
1600
Maximum Glass Temperature 1600C
Anode Voltage
1400 V
Anode Voltage 1400 wvolts
Shell Current
2 A
Shell Current 2 ma
Collector Voltage
1500 V
Collector Voltage 1500 wvolts
Collector Current
8 A
Collector Current 8 ma
Control Electrode Voltage (Note [1]
5 V
Control Electrode Voltage (Note 5) -15 volts
Control Electrode Voltage (Note [2]
-15 V
Control Electrode Voltage (Note 5) -15 volts
Power Output
100 W
Power Output 100 milliwatts
Bandwidth [1]
8 MHz
Bandwidth 8.0t0 9.6 kmc
Bandwidth [2]
9.6 MHz
Bandwidth 8.0t0 9.6 kmc
Gain over Bandwidth (Small Signal)
30
Gain over Bandwidth (Small Signal) 30 db min.
Gain over Bandwidth (Power)
25 W
Gain over Bandwidth (Power) 25 db min.
Beam
1
Beam 1.0
Note
1 V
Note 1: All voltages shown are with respect to cathode. Anode and helix are
Note
2 A
Note 2: The shell current is the difference between the cathode current and
current exceeds
3 V
current exceeds 3 ma, high voltage is removed.
Note [1]
3
Note 3: It is generally desirable to operate the collector at 100 volts positive
Note [2]
100
Note 3: It is generally desirable to operate the collector at 100 volts positive
Note
4
Note 4: Forced air cooling of collector is required for average collector
power in excess of
10 W
power in excess of 10 watts. As the collector power is increased,
Note
5 V
Note 5: The control electrode voltage is adjusted for maximum beam trans-
( [1]
2 V
(2) Turn on cooling air, solenoid voltage (adjust to approximately 1300 gauss),
( [2]
1300 V
(2) Turn on cooling air, solenoid voltage (adjust to approximately 1300 gauss),
(
3 V
(3) Raise high voltage to desired value, adjusting solenoid voltage and control
to exceed
3 A
to exceed 3 ma shell current. It may be necessary to rotate the tube in
(
4
(4) The above procedure is not required after initial set up; however, heater
applying high voltage. Observance of the
3 V
applying high voltage. Observance of the 3 ma maximum limit on shell
Published value [1]
8 A
8 20 collector current with shell
Published value [2]
20 A
8 20 collector current with shell
current less than
3 A
current less than 3 ma,.
Published value [1]
0 MHz
0 for maximum gain at f = 9. 0 kmc
Published value [2]
9 MHz
0 for maximum gain at f = 9. 0 kmc
Published value [3]
0 MHz
0 for maximum gain at f = 9. 0 kmc
Z8
30
Z8 30l Gain
Heater-Cathode A %) [1]
15
Heater-Cathode A %) 15/16
Heater-Cathode A %) [2]
16
Heater-Cathode A %) 15/16