Rectifier - Full Wave ·Rectifier-Rectifier
Indirectly heated full-wave high-vacuum rectifier for conventional AC power supplies. Heater-cathode isolation and relatively low forward drop suit receiver, amplifier, and general electronic equipment.
Full-wave indirectly heated high-vacuum rectifier.
International Octal
General specifications
Properties common to every published source and operating point.
Electrical assignments shared by every tube using this base designation.
| Terminal | Section | Connection | Evidence |
|---|---|---|---|
| PIN2H | — | H — Heater EIA chart transcription; manufacturer corroboration pending | Unverified EIA Base Connections, printed page 127, 5L |
| PIN4P1 | A | P — Plate (Anode) EIA chart transcription; manufacturer corroboration pending; preserve source designation P1 | Unverified EIA Base Connections, printed page 127, 5L |
| PIN6P2 | A | P — Plate (Anode) EIA chart transcription; manufacturer corroboration pending; preserve source designation P2 | Unverified EIA Base Connections, printed page 127, 5L |
| PIN8K | A | K — CathodeGroup 5L8 Second element on shared physical terminal; manufacturer confirmation pending | Unverified EIA Base Connections, printed page 127, 5L |
| PIN8H | — | H — HeaterGroup 5L8 EIA chart transcription; manufacturer corroboration pending | Unverified EIA Base Connections, printed page 127, 5L |
2 physical sections, each with unique specifications.
Section 1
Representative row for identical repeated sections.
Section 2
Second physical rectifier section; electrical properties populated from applicable published ratings.
Source-dependent data
Each block preserves the test conditions and published values from one reference. Values from different sources are intentionally kept separate.
Data set 01
Published operating points and test conditions from this source.
AC plate voltage per plate RMS
400 V
Peak inverse voltage
1100 V
DC output current
125 mA
AC plate voltage per plate RMS
400 V
Peak inverse voltage
1100 V
DC output current
125 mA
Data set 02
Published operating points and test conditions from this source.
Heater/filament voltage
5 V
Section1
Heater/filament current
2 A
Section1
RMS AC voltage per plate maximum
400 V
FullWave
Peak inverse voltage maximum
1100 V
FullWave
DC output current maximum
125 mA
FullWave
Average tube voltage drop
20 V
FullWave
Data set 03
Published operating points and test conditions from this source.
Heater or filament voltage
5 V
Published nominal value
Heater or filament current
2 A
Published nominal value
AC plate voltage per plate
400 V
Published
Peak inverse voltage
1100 V
Published
DC output current
125 mA
Published
Filter service
Capacitor-input or choke-input
Published
Data set 04
Published operating points and test conditions from this source.
HeaterVoltageNominal
5 V
Nominal
HeaterCurrentNominal
2 A
Nominal
Maximum Peak Inverse Voltage
1400 V
Rectified Output Current
125 mA
PeakForwardCurrent
375 mA
HeaterVoltageNominal
5 V
Nominal
HeaterCurrentNominal
2 A
Nominal
Maximum Peak Inverse Voltage
1400 V
Rectified Output Current
125 mA
PeakForwardCurrent
375 mA
Data set 05
Published operating points and test conditions from this source.
Maximum RMS supply voltage per plate
350 V
FullWave
Maximum DC output current
125 mA
FullWave
Maximum peak inverse voltage
1400 V
FullWave
Maximum peak current per plate
375 mA
FullWave
Tube voltage drop
20 V
At 125 mA DC output
Maximum RMS supply voltage per plate
350 V
FullWave
Data set 06
Published operating points and test conditions from this source.
AC Plate Voltage
350 V
CapacitorInputFilter
AC Plate Voltage
500 V
ChokeInputFilter
AC Plate Voltage
350 V
CapacitorInputFilter
AC Plate Voltage
500 V
ChokeInputFilter