Rectifier - Half Wave ·Rectifier
Miniature half-wave rectifier for 150 mA series-string line-operated equipment, with a tapped heater for a panel lamp. It provides conventional transformerless power-supply rectification.
The 50DC4 is a seven-pin miniature half-wave rectifier for line-operated series-heater equipment, with a heater tap for a panel lamp.
Miniature 7-contact
General specifications
Properties common to every published source and operating point.
Electrical assignments shared by every tube using this base designation.
No verified pinout is recorded for this base designation.
1 physical section, each with unique specifications.
Section 1
Nominal output current uses the maximum published no-panel-lamp DC output rating; panel-lamp cases are preserved as parameters.
Source-dependent data
Each block preserves the test conditions and published values from one reference. Values from different sources are intentionally kept separate.
Data set 01
Published operating points and test conditions from this source.
Heater voltage
50 V
Heater current
150 mA
Maximum AC plate voltage RMS
117 V
WithPanelLamp
Maximum DC output current
110 mA
WithPanelLamp
Heater tap voltage
7.5 V
WithoutPanelLamp
Filter input capacitor
40 uF
WithoutPanelLamp
DC output voltage at filter input
130 V
55mAOutput
DC output voltage at filter input
110 V
110mAOutput
Data set 02
Published operating points and test conditions from this source.
Maximum peak inverse plate voltage
330 V
HalfWaveRectifier
Maximum steady-state peak plate current
720 mA
HalfWaveRectifier
Maximum DC output current without panel lamp
120 mA
HalfWaveRectifier
Typical AC plate supply voltage
117 V
HalfWaveRectifier
Typical filter input capacitor
40 uF
CapacitorInputFilter
Typical DC output current
110 mA
HalfWaveRectifier
Rectifier maximum peak inverse voltage
330 V
PromotedValue
Rectifier nominal output current
120 mA
PromotedValue
Rectifier peak forward current
720 mA
PromotedValue
Rectifier maximum heater-cathode voltage
330 V
PromotedValue
Maximum Heater- Tap Voltage When Panel Lamp Fails I Rms
16.5 V
PublishedTable
Heater Positive With Respect To Cathode
330 V
PublishedTable
Heater Negative With Respect To Cathode
330 V
PublishedTable
Heater Voltage (Pin } To Pin 4) 45 45 45
45 V
PublishedTable
Heater —Tap Voltage (Pin 4 To Pin 6) 5.5 5.5 5.5
5.5 V
PublishedTable
Ac Plate- Supply Voltage S Rms 117 117 117
117 V
PublishedTable
Impedance 15 15 15
15 ohm
PublishedTable
Heater Current
150 mA
PublishedTable
Heater Voltage(Pin }To Pin 4)
50 V
PublishedTable
Neater-Tap Voltage (Pin 4 To Pin 6)
7.5 V
PublishedTable
Heater Current (Between Pins } ~ ¢)
150 mA
PublishedTable
Total Effective Plate- Supply Impedance
15 ohm
PublishedTable
Dc Output Current
110 mA
PublishedTable
For Dc Output Current Of 55 Ma.
130 V
PublishedTable
Tube voltage drop at 240 mA
21 V
Rectifier forward voltage drop
21 V
PromotedValue
Ax 50T10~ Volts
150 mA
PublishedTable
Data set 03
Published operating points and test conditions from this source.
DC Output Current
70 mA
WithPanelLamp
DC Output Current
80 mA
WithPanelLamp
DC Output Current
90 mA
WithPanelLamp
DC Output Current
100 mA
WithPanelLamp
DC Output Current
110 mA
WithoutPanelLamp
AC Plate-Supply Voltage RMS
117 V
Filter Input Capacitor
40 uF
CapacitorInputFilter
Tube Voltage Drop
21 V
Ib=240mA
Data set 04
Published operating points and test conditions from this source.
Peak Inverse Voltage
330 V
DC Output Current
110 mA
Panel-Lamp Heater Section Voltage
7.5 V